Advanced kit – 800/900 hrs
Each kit provided by Flying Legend includes the fuselage kit, the wing kit, the empennage kit, the flight control kit, the fixed landing gear kit, the aluminium tank kit and the canopy kit. Each kit includes also all the hardware parts (bolts, nuts, rivets and so on) required to assembly the aircarft. A amateur builder requires approximately 800/900 hrs to complete the advanced kit.
The standard kit does not include the retractable gear. The retractable gear has to be selected in the option list
Entirely made in Aluminium 2024-T3/6061 -T6, the structure is calculated for a MTOW of 650,00 kg and a load factor of +6/-3G or 750,00 kg with a load factor +4.4/-2.2 G
What is included in the advanced kit?
Fuselage Kit
-Fuselage central body closed and upper fuselage partially closed
-skins not assembled are pre-punched at 2.4 mm, cutted and rimmed
-Engine mount blocks are included
the amateur builder has to cleco what is left, re-drill the holes to the final size before riveting and assembly the internal parts.
-floor sheets
-internal side upholstery
-canopy closure parts
-roll bar
-extra luggage compartment parts
-pedals supports
-ss cowling frame
-harware
FL supplies also the material required for the fuel system as standard aluminum fuel pipes which are installed under the floor.
The fuselage is also provided with inspection windows which allows the builder an easy access to the internal components.
Half Wing Kit
-back Wing, its partial belly and the first part of the nose wing are supplied completely closed
-open wing nose (pre-pounched) to install the tanks
-Partial the electric cables passage and the additional fuel tank supports
-wheel comparment, remaining nose, fuselage front spar and footsteps pre-punched at 2.4 mm
-close the FLAP and the AILERON
-inspection windows
Empennage kit
-pre assembled with guide holes of 2.4mm
-the skins are cutted and rimmed to the final size.
-the builder has to size the holes to the final size, insert the counterbalance and close
-trim kit (not supplied) to be assembled
Flight control
The kit includes all the parts necessary to realize the flight control of the aircraft, the pedals and all the other elements in chrome molybdenum already welded and treated with powder paint by FL. The amateur builder will have to assemble the aluminium parts and all the other items where the bearings and uniball are placed.
Fixed Undercarriage
-leaf spring made of aluminium, with 4 supports to fix the structure,
– two 6″ wheels which are working with manual brakes,
– a front undercarriage with a 4″ wheel
ATTENTION: At the time of the order please specify if you would like the fixed or retractable undercarriage option as the fuselage and the wings have to be structured accordingly – also the front undercarriage is suitable for our engine mount.
Tank kit
-n.2 unassemble aluminium tanks (15.5 gal each) including the required accessories and harware to install them in the wings
-accessories: fuel caps, fuel vent, fuel inlet, fuel drain valve
-the mastic is not supplied due of the fact that it expires so it is recommended to buy it at the time of usage.
Resin Kit
-cockpit cover
-bottom rudder tip
-wing cover
-stabilizer cover
-dorsal fin
Canopy kit
– clear bubble canopy (grey and blu available with additional cost)
-frame
The canopy is manufactured on a tailor made stamp, designed from FL.
It provides a great visibility either from the front and the rear seat.
–Fuel sensor
–The items/service below are NOT included in the standard kit offer but you can add them as an option
–Wheel Fairing Kit
–Toe brakes on pedals
–Parking break
-Retractable gear kit
-main and nose powder coated landing gear
-mechanics
-bushings
-hydraulic cylinders
-hydraulic power pack (12V)
-switches and electric components
-wheels with hydraulic brakes
-emergency manual pump to release the gear in case of failure
-hose and fittings
–Assembled tanks service
–Explode Safe Bladder Tanks
– n.2 bladder tanks (total capacity 25 gallons) complete with accessories to place them in the wings,
-caps (NEWTON),
–Resin Tip kit
-elevator tip
-stabilizer tip
-fin tip,
-rudder tip
-half wing tips
–Upper and Lower Cowl kit
–Clear Wing tips
–Canopy assemblage service
-Engine Mount kit
It is suitable for Rotax Engine, either 912 and 914.
It can be also used for the experimental engine of 140 hp.
–Rotax Ring
If you are going to purchase the Rotax 914 please do not include it as it is already provided by Rotax.
–Engine mount isolator (4 units)
–Standard seat
made of resin, not fabric covered
–Structural seat
The structural seats allow the belts to be installed on the seats directly and not on the aircraft structure.
They are not fabric covered resin seats with aluminum structure.
This seat is 2,36 inch higher, therefore has to be evaluated for pilots taller than 5,9ft
–Standard seats with fabric cover and FL logo
–Rear brake (only manual)
–Electric trim
–Throttle system
–Rear instrument panel
Instrument panel is provided plain as we do not know which instruments the customer would like to add.
However if the customer already knows which instruments he would like, we can laser cut the holes.
The same applies for the front instrument panel which is already included in the kit price
-Entry step
–Faux Exhaust Ducts
–Spinner and backing plate
–Engine Accessory kit
It includes
-fuel line Rotax engine with supercharger (it does not include the 2 electric fuel pump)
-oil tank supports
-radiator supports (it does not include the radiator)
-water hose supports
The image below will show you the items supplied and their installation